Showing all 6 results

Model 21-80 BS (Special Application Pump)
The SPECK Model 21-80 BS is a high efficiency plastic pool pump. The Model 21-80 BS is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. This pump design provides maximum flow at low head and has 250 cubic inch all plastic strainer tank, and is self-priming up to 4 feet. Features This high volume, low head pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour. The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 800-223-8538) Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F. For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
Read More » Request A Quote »
The SPECK Model 21-80 BS is a high efficiency plastic pool pump. The Model 21-80 BS is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. This pump design provides maximum flow at low head and has 250 cubic inch all plastic strainer tank, and is self-priming up to 4 feet. Features
• This high volume, low head pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour. The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 800-223-8538)
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175^° F.
• For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
• All models are equipped with 4″ female slip adaptor on suction of strainer tank and 4″ male slip adaptors on the discharge.
• Heavy duty “1081” E-plus® /extreme-E™ energy efficient pool motors for extra low energy consumption. This large 56 frame motor is thermally protected, has a PSC switchless design and extra large sealed ball bearings. (No motor starter required)
• Motor is easy to remove without disturbing the plumbing. Reusable o-rings throughout.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message




Model 21-80 G (BADU SwimJet & Special Application Pump, Flooded Suction)
The Speck Model 21-80 G is a high efficiency plastic pool pump. The Model 21-80 is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. This pump design provides maximum flow at low head and is available in two version: flooded suction or self-priming. Features This high performance pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour. The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538) Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F. For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts. All models are equipped
Read More » Request A Quote »
The Speck Model 21-80 G is a high efficiency plastic pool pump. The Model 21-80 is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. This pump design provides maximum flow at low head and is available in two version: flooded suction or self-priming. Features
• This high performance pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour.
• The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538)
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F.
• For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
• All models are equipped with 4″ quick disconnect unions.
• Heavy duty “1081” E-plus® /extreme-E™ energy efficient pool motors for extra low energy consumption. This large 56 frame motor is thermally protected, has a PSC switchless design and extra large sealed ball bearings. (No motor starter required)
• Motor is easy to remove without disturbing the plumbing. Reusable o-rings throughout.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message




Model 21-80 GS (BADU SwimJet & Special Application Pump, Self-Priming)
The Speck Model 21-80 GS is a high efficiency self-priming plastic pool pump. The Model 21-80 GS is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. Features This high performance pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour. The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538) Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F. For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts. All models are equipped with 4″ quick disconnect unions. Heavy duty “1081” E-plus® /extreme-E™ energy
Read More » Request A Quote »
The Speck Model 21-80 GS is a high efficiency self-priming plastic pool pump. The Model 21-80 GS is ideally suited for commercial vacuum and sand filters, hydrotherapy, swim spas, waterfalls, water slides, and vanishing edge pool applications. Features
• This high performance pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour.
• The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538)
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F.
• For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
• All models are equipped with 4″ quick disconnect unions.
• Heavy duty “1081” E-plus® /extreme-E™ energy efficient pool motor with large 56 frame is thermally protected (no motor starter required). PSC switchless design and extra large sealed ball bearings.
• Motor is easy to remove without disturbing the plumbing. Reusable o-rings throughout.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message




Model 21-80/30 G (Vanishing Edge & Water Feature Pump)
The Speck Model 21-80/30G is a high efficiency plastic Special Water Feature Pump. The Model 21-80/30G is ideally suited for pools with a vanishing edge, waterfall, fountain, or water slide application. The flooded suction pump design provides maximum flow at low head and is extremely quiet due to a large 4″ suction and discharge and low RPM motor (1750 RPM). Features This high volume, low head pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour. The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538) Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F. For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts. Suctio
Read More » Request A Quote »
The Speck Model 21-80/30G is a high efficiency plastic Special Water Feature Pump. The Model 21-80/30G is ideally suited for pools with a vanishing edge, waterfall, fountain, or water slide application. The flooded suction pump design provides maximum flow at low head and is extremely quiet due to a large 4″ suction and discharge and low RPM motor (1750 RPM). Features
• This high volume, low head pump comes complete with our unique mechanical shaft seal that allows the pump, if mistreated, to run dry for up to one hour.
• The pump can be used for pool water with a salt concentration of up to 5000 ppm. (For a high concentration please call 1-800-223-8538)
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 175° F.
• For pool users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
• Suction and discharge are equipped with 4″ quick disconnect unions for easy installation and maintenance.
• Heavy duty “1081” E-plus® /extreme-E™ energy efficient pool motor with large 56 frame is thermally protected, has a PSC switchless design and extra large sealed ball bearings.
• Motor is easy to remove without disturbing the plumbing. Reusable o-rings throughout.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message




Model E45 (Jetted Bathtub Pump)
The Speck Model E45 jetted bathtub pump has been engineered for durability and economy. Special design allows all water to drain from the pump. All models are equipped with 1.5″ quick disconnect unions. Features This high performance, medium head pump comes complete with an industry standard carbon/ceramic 5/8″ mechanical seal for convenient replacement. Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 150° F. Suction and discharge ports are equipped with 1.5″ quick disconnect unions. (Optional 1.5″ NPT connection also available.) For tub users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the water and electric parts. Pump is equipped with durable, special 48 frame thru-bolt mount energy efficient PSC motor with stainless steel shaft. Pump is also available with a specially design
Read More » Request A Quote »
The Speck Model E45 jetted bathtub pump has been engineered for durability and economy. Special design allows all water to drain from the pump. All models are equipped with 1.5″ quick disconnect unions. Features
• This high performance, medium head pump comes complete with an industry standard carbon/ceramic 5/8″ mechanical seal for convenient replacement.
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 150° F.
• Suction and discharge ports are equipped with 1.5″ quick disconnect unions. (Optional 1.5″ NPT connection also available.)
• For tub users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the water and electric parts.
• Pump is equipped with durable, special 48 frame thru-bolt mount energy efficient PSC motor with stainless steel shaft.
• Pump is also available with a specially designed 42 frame motor with built-in air switch.
• The Model E45 comes standard 3ft. 3/12 AWG cord set and built-in air switch. A variety of cord sets are available.
• Special design allows all water to drain from the pump casing.
• Motor is easy to remove without disturbing the plumbing. Reusable o-rings throughout.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message




Model E75 – Spa Pump
The Speck Model E75 spa pump has been engineered for durability and quiet performance with economy in mind. All models are available with single or two speed motors. Features This high performance, medium head pump comes complete with an industry standard Carbon/ceramic 5/8″ mechanical seal for convenient replacement. Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 150° F. For spa users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts. Pump is equipped with durable, economical 48 frame thru-bolt mount motor with stainless steel shaft. Suction and discharge ports are equipped with 2″ quick disconnect unions. (The Model E75-I comes standard with 1.5″ quick disconnect unions.) A variety of cord sets are available. The Model E75 is available
Read More » Request A Quote »
The Speck Model E75 spa pump has been engineered for durability and quiet performance with economy in mind. All models are available with single or two speed motors. Features
• This high performance, medium head pump comes complete with an industry standard Carbon/ceramic 5/8″ mechanical seal for convenient replacement.
• Non-corrosive, chemical/UV resistant, and can withstand temperatures of up to 150° F.
• For spa users’ safety, the impeller has a dielectric shaft sleeve that provides absolute separation between the pool water and electric parts.
• Pump is equipped with durable, economical 48 frame thru-bolt mount motor with stainless steel shaft.
• Suction and discharge ports are equipped with 2″ quick disconnect unions. (The Model E75-I comes standard with 1.5″ quick disconnect unions.)
• A variety of cord sets are available.
• The Model E75 is available with 115V or 230V motor in single or 2-speed.
• Every pump is performance tested before leaving the Speck factory.
Read Less » Request A Quote »






Your Name



Your Phone



Your email



Your subject



Your message